Introduction:

The enclosed fiber laser marking can use for most of area, such as factories, shops, personal processing shops; Metal jewelry marking, handicraft lettering, metal parts marking and coding, plastic parts marking lettering, molds marking, precious metals marking, etc; It can engrave all kinds of metal, some plastic such as: ABS, PE etc; Easy to use and no maintenance, which use for 24 hours with longer laser life.

Applicable materials:

※ Common metals and alloys: steel, stainless steel, iron, copper, brass, aluminum, magnesium, zinc and other metals.

※ Rare metals and alloys: gold, silver, titanium

※ Metal oxide, special surface treatment (phosphating, aluminum anodizing, electroplating surface)

※ Common non-metals: plastic(ABS, PVC, PE, PET, etc), hard board.

Applicable industries:

※ Hardware products, tool accessories, precision equipment, glasses and watches, jewelry, auto parts, plastic buttons, building materials, food, medicine, electronic components, integrated circuits (IC), electrical appliances, mobile phone communications, PVC pipes, sanitary ware, etc.

Advantages:

※ High efficiency

※ Higher flexibility when integrated into system

※ High performance

※ Faster engraving speed

※ Easy operation

※ High photoelectric conversion efficiency

※ Smaller beam spot size.

※ Long lifetime: maximum can be 100, 000 hours

※ Rich extensions: rotary system, xy table, etc.

※ Support formats: PLT, DXF, BMP, JPG, and so on

Parameters

Model	DS-LM20	DS-LM30	DS-LM50	DS-LM80
Laser power output	20W	30W	50W	80W
Laser wavelength	1064±10 nm
Marking area	100x100mm(standard)/175x175mm/200x200mm
Pulse frequency	20~80KHZ/1~600KHZ/1~2000KHZ/1~4000
Max marking speed	9000mm/s
Repeat accuracy	±0.001mm
Min.line width	0.01mm
Min.character size	0.2mm
Cooling	Air cooled
Working temp	10~35 ℃
Humidity range	< 70% No condensation
Power supply	AC220V±10%, 50Hz or AC110V±10%, 60Hz

Daily Maintenance

1. Clean the dust, dirt and foreign matter inside the equipment, use a vacuum cleaner, alcohol and dust-free cloth to remove dust, dirt and foreign objects;

2. Check whether the focal length is within the range of the standard focal length, and test that the laser reaches the strongest state;

3. Check whether the lens of the field lens is dirty, wipe with lens cleaning paper;

4. Check whether the parameter setting screen on the laser is normal and the laser parameters are within the setting range;

5. Whether the machine is turned on normally, whether the machine main switch, laser control switch, and laser marking system switch are turned on normally;

6. Confirm that the switch is normal and effective. After pressing the switch, check whether it is energized; whether the laser is working normally.

Weekly Maintenance

1. Keep the machine clean and clean the surface and interior of the machine;

2. Check whether the red light preview can be turned on normally, the laser parameters are within the setting range, open the red light correction on the software to turn on the red light;

3. To clean the laser field lens, first use special lens cleaning paper dipped in alcohol to wipe in one direction, and then wipe it with dry lens cleaning paper;

4. Check whether the laser light is normal, open the software and start manual marking for laser test.

Monthly Maintenance

1. Check the lifting rail for looseness, abnormal noise, oil leakage, clean with a dust-free cloth and add lubricating oil;

2. Clean the dust at the air outlet of the laser to ensure normal heat dissipation. Clean the dust, waste nodes and other foreign objects inside the equipment, use a vacuum cleaner, alcohol and dust-free cloth to remove dust, dirt and foreign objects;

3. Check whether the laser light emitted by the laser becomes weak, use a power meter to test;

4. Check whether there is any looseness in the power plug and each connection cable connector, check each connector part; whether there is poor contact;

5. Check whether the red preview light path is shifted and perform red light correction.

Annual Maintenance

1. Check the laser cooling fan, whether it rotates normally, and clean the laser power supply and control board dust;

2. Check whether each motion axis is loose, abnormal noise, smooth operation, clean with a dust-free cloth and add lubricating oil.

Precautions

1. Please wear protective glasses when working to avoid stimulating the bright light to damage the glasses;

2. Special attention is forbidden to put your hand within the laser scanning range during use;

3. When the machine is improperly operated, resulting in an emergency, immediately press the power off;

4. To prevent electric shock, do not operate with wet hands;

5. During the operation of the machine, do not put your head or hand into the machine to avoid personal injury;

6. No specific system parameters may be changed at will without the permission of the equipment technician.

Samples

FAQ

Q1: How to choose the suitable power of laser ?

A: The power of the fiber laser marking machine is: 20 watts, 30 watts, 50 watts, 70 watts, 100 watts, 120 watts, etc. The fiber laser marking machines are mainly used in metals, alloys and oxides, ABS, epoxy, etc. Electronic components, hardware, gold and silver jewelry, glasses, clocks, power switches, etc., general materials can be beautifully printed with 20 watts. Some materials that require marking depth need to be tested with 30 watts for proofing first, and some materials Only 20 watts of power can be used to produce satisfactory results, and 30 watts of power cannot be used. Some materials can only use 30 watts of power to achieve the desired effect, and 20 watts can not achieve the desired effect. The actual situation still needs proofing for judgment.

Q2: How is the shipping method?

A: As per your actual address, we can effect shipment by sea, by air, by truck or railway. Also we can send the machine to your office as per your requirement .

Q3: What's consumables of laser marking machine?

A: It does not have consumable. It's very economical and cost effective.

Q4: What's package, will it protect the products?

A: We have 3 layers package. For the outside, we adopt wooden cases free of fumigation. In the middle, the machine is covered by foam, to protect the machine from shaking. For the inside layer, the machine is covered by waterproof plastic film.

http://www.dotslasermachine.com/